Advertisement

eero mesh wifi loses internet after modem restart

If eero drops internet right after a modem restart, the problem is usually the modem handoff, a stale WAN lease, or bridge-mode/MAC-lock behavior. This article shows the fastest check order so you can bring service back without guessing.

Networking 9 min read
A mesh Wi‑Fi router sits next to a modem on a shelf with Ethernet cables connected.

If your eero mesh loses internet right after a modem restart, the modem usually hasn’t finished coming back online, hasn’t handed eero a fresh WAN lease, or has a bridge-mode/MAC-lock setting that changed the handoff. The fastest fix is to check the modem first, let it settle fully, then restart only the gateway eero and bring the satellites back later. If the modem still won’t pass internet on its own, the problem is upstream and the ISP needs to look at the line or modem handoff.

What you’ll usually see

This problem often starts right after you reboot the modem, swap cables, or change something on an ISP combo box. The eero app may still show the network as reachable locally, but it says there’s no internet, or devices on Wi‑Fi can’t get out to the web even though the eero lights look normal.

A useful way to read the symptom is this: if the Wi‑Fi inside the house is working but the app says the network is offline, that points to the WAN side — the link between the modem and the gateway eero — rather than a pure Wi‑Fi problem. If every eero goes offline at once right after the modem restarts, that is usually not a mesh-only failure; the gateway lost its upstream connection and the rest of the mesh followed.

Before you start

  • Make sure the modem or fiber ONT is the device that actually connects to your ISP.
  • Know which eero is the gateway, meaning the one wired to the modem.
  • If your ISP box is a modem/router combo, be ready for bridge mode or router mode to matter after a reboot.
  • Don’t keep power-cycling everything over and over. That can make the handoff harder to read and can stretch the outage.
  • If the modem’s status lights never settle or it never gets service on its own, stop treating this as an eero problem and move to the ISP side.

The first thing to check is the modem itself. Before you touch the eeros, confirm it is fully online on its own, not just powered on. eero support says to wait for the modem to come back online, then restart the gateway and wait until it has a solid white LED light.

The safe restart order

  1. Leave the satellites alone for the moment and focus on the modem and the gateway eero first.
  1. Unplug power from the modem or fiber ONT. If it’s an ISP combo box, give it enough time to fully power down; eero support says to unplug it for at least 3 minutes and then plug it back in.
  1. Wait for the modem to settle before reconnecting anything else. In practice, that means watching for it to finish booting, re-establish its internet light, and stop cycling through startup states. Some connections take 5-10 minutes to regain connectivity.
  1. Once the modem is fully online, plug in only the gateway eero. Do not bring the satellites back yet.
  1. Wait for the gateway eero to finish booting and check the LED. Surf Internet says a successful reboot should move from blinking white to solid white.
  1. If the gateway comes back online, power up the other eeros one at a time.

If the gateway still can’t get internet after that sequence, don’t keep repeating the same reboot. At that point, the remaining possibilities are usually a WAN lease problem, a modem/router handoff problem, or an ISP issue upstream.

A modem and gateway eero router are shown with the network cable unplugged during a restart.

How to tell WAN lease trouble from a Wi‑Fi-only problem

A WAN lease problem shows up when the gateway eero can stay powered and your phone can still see the local network, but the app says there’s no internet or the gateway never gets a usable connection from the modem. In plain terms, the local Wi‑Fi may be up while the outside connection is dead.

A Wi‑Fi-only problem looks different. If the modem has service and the gateway eero has a solid white light, but one room or one satellite still acts flaky, that’s more likely a placement, interference, or individual node issue. Astound’s troubleshooting notes that if multiple eeros are affected, you should restart them individually rather than assuming one reboot fixed the whole mesh.

Use this quick check: if the modem itself is not online, the problem is upstream. If the modem is online but the gateway eero still cannot get internet after the correct restart order, look at the WAN handoff, DHCP, or bridge settings. If only part of the house is affected, that’s more likely a Wi‑Fi coverage issue than a modem restart issue.

Bridge mode, MAC lock, and delayed DHCP

Bridge mode changes who does the routing. If the ISP box is in bridge mode, it should hand the connection off cleanly to eero and let eero be the router. If that setting reset, or if the combo unit is still trying to route on its own, the gateway may not get the clean Ethernet handoff it expects.

MAC lock can also interfere. Some ISP equipment remembers the first device it saw on the WAN side and expects that same device identity to come back. After a reboot, that can leave eero waiting for a fresh lease while the modem is still tied to the old session.

Delayed DHCP is another common cause. DHCP is the process that hands out an IP address. If the modem or ISP side is slow to issue one, eero can look powered and healthy while still sitting there with no WAN address. A support guide specifically calls out slow DHCP as a reason reconnection can take longer than expected.

The practical move here is patience and order, not more resets. Leave the modem alone until it is clearly settled, then connect the gateway eero once. If you reconnect too early, the modem may not relearn the handoff cleanly, especially on a combo device.

When the ISP needs to fix the line or modem handoff

The ISP needs to step in when the modem never becomes fully online by itself, when the connection drops again right after the correct restart sequence, or when the modem’s status never stabilizes even though you’ve given it time to settle.

A good clue is what the app says after you reconnect the gateway. eero support says you can connect your phone to the eero network and still see troubleshooting details in the app even if the network is offline. If the local network is reachable but the app still shows no internet, that is a WAN-side problem, not a Wi‑Fi-only problem.

If the modem/router combo is in bridge mode and still won’t hand off cleanly after a proper power cycle, that’s also a strong sign the ISP box or the ISP line needs attention. At that point, there isn’t much value in rebooting the satellites or moving nodes around. The issue is before the mesh.

What to do if the app still says there’s no internet

If the eero app still shows no internet after you’ve followed the modem-first sequence, check the modem status one more time before changing anything else. If the modem is offline, call the ISP. If the modem is online but the gateway eero still won’t recover, try one clean gateway restart after the modem has fully settled, then stop.

If the app still shows no internet and the modem looks healthy, the likely next step is to contact the ISP or eero support with the modem’s status details, the exact restart order you used, and whether the problem changes when the gateway eero is the only device plugged in. That information usually saves time because it separates a bad line from a bad handoff.

Verify the fix

You’ve got it back when the modem is fully online, the gateway eero shows a solid white LED, the eero app says the network is back online, and devices can reach the internet again. eero support says the app will let you know once the internet connection is back online.

If the gateway is online but one or more satellites still misbehave, power those units up again one at a time and watch whether they return to a normal white status. If a specific node keeps dropping after the rest of the network is healthy, that is a separate mesh issue, not the modem restart problem you started with.

Conclusion

If the modem won’t settle, call the ISP. If the modem is stable but eero still won’t recover after the safe restart order, the handoff or lease is the next thing to inspect.

Frequently Asked Questions

How do I tell if the modem is the problem or the eero is the problem?

Check the modem first. If it can’t get online by itself, the problem is upstream. If the modem is online but the gateway eero still has no internet after the correct restart order, the issue is usually the WAN handoff, DHCP renewal, bridge mode, or a modem/router combo setting.

Should I restart the modem or the eero first?

Restart the modem first, wait for it to fully come back online, and then reconnect the gateway eero. eero support and other troubleshooting guides use that order because reconnecting eero too early can leave it waiting on a half-ready modem or a stale WAN lease.

Sources