A reconnect after an eero firmware update can be normal for a short time. eero says the network may restart during the update, and connected devices should reconnect automatically once it finishes. If devices keep dropping after that, one node stays offline, or the same problem comes back after every update, treat it as a real fault. Work from the affected client outward to the node and then the modem.
When a reconnect after an eero update is normal
A brief reconnect right after an eero firmware update is expected. eero says the network may restart during the update, and the update normally takes only a few minutes. Some firmware changes can also trigger more than one restart. So a short outage by itself does not mean the update failed.
What is not normal is a device that keeps asking to reconnect long after the network should have settled. It is also not normal when one eero never comes back in the app, or a home only works after repeated reboots. If that is what you see, you are past the normal update window and into troubleshooting.
| Symptom pattern | Most likely layer |
|---|---|
| One phone, laptop, TV, or IoT device keeps dropping | That client device |
| Several devices in one room or on one area of the mesh drop together | The nearest eero node |
| The whole home goes unstable or the gateway looks offline | Gateway, modem, or mesh-wide issue |
| The same reconnect problem shows up after every firmware update | A recurring node, client, or settings problem |
A key clue is whether some devices still work. If the network is generally up and only one stubborn device keeps failing, that usually points to the client first, not the whole mesh.
Before you start
Before you reboot anything, check the eero app and wait long enough to separate a normal restart from a stuck update. eero notes that an update can momentarily take the network offline, and connected devices should come back when it finishes. If the app still shows an update in progress or the system only just restarted, give it a few minutes before changing anything.
Check these things first:
- Whether the gateway eero is online in the app.
- Whether any satellite node is missing, offline, or still coming back.
- Whether the app shows all units on the same firmware version.
- Whether only one device, one room, or one type of device is affected.
Stop and wait if the app still shows the network settling and devices are gradually returning. Move on only when the network has had time to finish and the same problem is still there.
Check what actually broke: one device, one node, or the whole mesh
Use the failure pattern to narrow the fix before you touch power. That saves time, because a lot of post-update complaints are really one client that never rejoined cleanly.
If only one device is failing, start with the client. Forget that Wi‑Fi network on the device and join it again. That is the least disruptive fix, and it avoids touching healthy nodes.
If several devices in one part of the house failed together, look at the nearest eero node. A node that came back badly after an update can leave nearby clients stranded even while the rest of the mesh looks fine.
If the gateway is offline in the app, or everything dropped at once, this is a broader network problem. At that point, move past a single device and start checking the modem and the main eero path.
The safest recovery order that avoids extra downtime
Use the narrowest fix first. Only widen the scope if the problem stays put. The safest order is: reconnect the affected client, power-cycle the affected node, reboot the modem and then the eero, and only then remove, re-add, or reset anything that still will not recover.
- Reconnect the affected client first.
If one phone, laptop, TV, or smart device is the only thing failing, forget the network on that device and join it again. If it comes back and stays connected, stop there. If the same device still drops while everything else works, the problem is probably local to that client.
- Power-cycle the affected eero node.
If the app shows one node missing, offline, or suspiciously slow to return, unplug that node, wait briefly, and plug it back in. Watch whether the devices near that node recover. If they do, the problem was likely a node that did not rejoin cleanly after the update.
- Reboot the modem, then the eero system.
For reconnections that are still dragging on after the earlier steps, restart the modem first, let it fully connect, then power on the eero. That order matters when the mesh is healthy enough to come back but the upstream path is stuck. If the modem comes up and the eero network stabilizes, the issue was likely a bad handoff during the reboot.
- Remove and re-add, or reset, only if the problem persists.
If a specific eero keeps failing to return in the app, remove and re-add it in the app only after the simpler recovery steps fail. If a device still will not stay online after a fresh join, then forget and rejoin that device again. A soft reset or factory reset is a last resort, not the next move.
If the problem clears after one step, stop there. Repeating more changes makes it harder to tell whether the mesh recovered on its own or whether you actually fixed the fault.
Settings that can make post-update reconnects worse
A firmware update can expose settings that were already marginal. The usual trouble spots are DHCP behavior, reserved IPs, band steering, and stale device records.
DHCP is the part of the network that gives devices an address. eero support and community reports mention firmware versions where DHCP-related behavior and connectivity problems showed up together. If devices suddenly seem connected but cannot stay online after an update, check whether the app shows all nodes on the same firmware and whether any address-handling settings were changed recently.
Reserved IPs can also cause trouble if a reservation no longer matches the device you think it does. If you replaced hardware, renamed a client, or moved a node, confirm that the reservation still points to the right device.
Band steering can make a weak or older client look worse after an update if the client keeps getting pushed between bands and never settles. That is not automatically a broken mesh, but it can be enough to make one stubborn device keep reconnecting.
Stale device records can hang around after restarts or updates. If the app shows an old name, a duplicate entry, or a device that clearly exists but still appears offline, remove the old entry only when you are sure it is the same device and the simpler reconnect steps did not help.
Because behavior can vary by model and firmware version, check the current eero support docs for your exact hardware before changing advanced settings. A setting that helps one network can make another one worse.
When to escalate instead of waiting it out
Stop waiting when the same problem does not clear after the normal update window, or when one node keeps failing to come back cleanly. A healthy update should not leave you with one missing eero, a network that only works after repeated reboots, or the same device asking to reconnect every time.
Signs the update may have failed or a node did not recover cleanly include:
- One eero stays offline or never reappears in the app.
- Devices on that node keep dropping after each reboot.
- The app still shows units on different firmware versions.
- The same reconnect problem returns after every firmware update.
If the same issue happens after every firmware update, treat it as a pattern, not a one-off glitch. The repeating fault is usually a specific node, a specific client, or a setting that the update keeps exposing. At that point, collect the app status, note which devices and nodes drop, and contact eero support with that pattern instead of cycling through the same resets.
If one specific eero always follows the problem, remove and re-add that node rather than resetting the entire house over and over. If only one device repeats the issue, focus on that device instead of rebuilding the mesh.
Verify
After the fix, check that the gateway is online, the affected node is visible in the app, and the problem device stays connected long enough to use normally. If the app shows all units on the same firmware version and the same devices are no longer dropping, the recovery worked.
If the same reconnect problem returns on the next firmware update, go back to the step that matched the failure pattern instead of starting over with a full reset.
Conclusion
If the reconnect only happened during the update window, you probably only needed to wait. If it keeps happening, follow the order above and stop as soon as the unstable layer is fixed.
Frequently Asked Questions
Should I reboot the modem first after an eero firmware update?
Not usually. Start with the affected device or node first. If the wider network is still unstable after that, restart the modem first, let it fully connect, then power on the eero.
When should I forget and rejoin a device?
Do it when one device keeps asking to reconnect while the rest of the mesh looks fine. If several devices fail together, check the node or gateway first so you do not waste time re-adding a healthy client.
What if the same reconnect problem happens after every firmware update?
That points to a repeating node, client, or settings issue rather than normal update churn. Check which layer fails each time, note the firmware versions shown in the app, and escalate with that pattern instead of resetting everything again.
Sources
- Why does my eero app say "Your network needs an update"? | eero Support (eero.com)
- How do eeroOS updates work? | eero Support (eero.com)
- Guide on how to fix eero going offline & rebooting (astound.com)
- EERO v6.0.4 dropping internet connection - Discussion Topics - eero Community (community.eero.com)
- eero stability issues after upgrade to 7.0.0 - Discussion Topics - eero Community (community.eero.com)