If your Intel BE200 Wi‑Fi 7 adapter seems to forget the password after a reboot, the saved password usually is still there. In practice, this is most often a Windows profile problem, a BE200 driver reconnect problem, or a router security mismatch. Check the saved network and Windows power settings first, then the driver, then the router.
What this symptom usually means
People usually describe three different failures the same way: the Wi‑Fi profile is actually missing, Windows keeps asking for the password even though the profile exists, or the BE200 reconnects poorly after restart and makes it look like the password was lost.
The quickest clue is what happens after startup. If the SSID is no longer in the saved networks list, you’re looking at a Windows profile problem. If the network is still saved but Windows prompts again or fails to connect, the profile is probably present and the problem is happening during reconnect or authentication.
A cold reboot is the best test here. If Wi‑Fi works normally during a live session but fails after a restart, the issue is often tied to Fast Startup, sleep or hibernate state restoration, adapter power management, or a driver/router mismatch rather than a password that truly disappeared.
Before you start
Work through the checks in this order so you don’t erase the evidence too early.
- Confirm whether the saved network is still listed in Windows Wi‑Fi settings.
- Test the same router with another device.
- Test the BE200 on another Wi‑Fi network if you can.
- Note whether the problem happens after a normal reboot, after shutdown, after sleep, or after hibernate.
That split tells you where to focus. If only one network fails, the router or access point is more likely. If the BE200 fails on more than one network, look first at Windows, the driver, or adapter power behavior. If the problem only shows up after shutdown or resume, Fast Startup or power-state handling is a stronger suspect than the saved password itself.
Fix order
- Open the saved Wi‑Fi network in Windows and check that the SSID is still present and auto-connect is enabled.
If the network is missing, recreate it once with the current password. If it is present but reconnect still fails, stop treating this as a simple forgotten-password problem and move to the next step.
- Test Fast Startup and the reboot path.
Fast Startup can make shutdown behave differently from a true restart, and that difference can make a wireless profile look broken when it isn’t. Try a full restart, then a full shutdown and power-on, and compare the result. If the BE200 only fails in one of those paths, Fast Startup or another power-state transition is probably involved.
- Check adapter power management in Device Manager.
On some systems, Windows powers down the wireless adapter too aggressively. If the BE200 shows the network again but won’t authenticate after reboot or resume, disable the adapter’s aggressive power saving and test again. If that changes the behavior, you’ve found a reconnect problem rather than a lost password.
- Update the Intel BE200 driver from the laptop or motherboard vendor first.
Use the newest driver package that your board or system vendor currently supports, then retest after a reboot. If the problem started right after a driver update, roll back one version and compare behavior. That is usually the cleanest way to separate a driver regression from a router issue.
- Check the router or access point settings that affect reauthentication.
Security mode changes are a common trigger, especially if the router was moved between WPA2, WPA3, or mixed WPA2/WPA3 mode. A saved profile can still appear healthy in Windows while the adapter rejects it after reboot because the access point’s security negotiation no longer matches the stored profile. Also check band steering and any Wi‑Fi 7 compatibility settings if they were changed recently.
If the router was adjusted shortly before the problem started, match Windows to the router’s current security mode, then rebuild the profile once. Don’t keep changing both sides at once or you’ll lose the clue about which change caused the break.
- Delete and rebuild the saved network only when the profile is likely corrupted or out of sync.
That’s the right move when the SSID is still visible, the password is correct, the Windows settings look normal, and the reconnect problem survives a driver check and a router check. It’s the wrong move if you still need to tell whether Windows, the BE200, or the router is at fault.
If a fresh profile fixes it once and then the problem comes back after reboot, the old profile was probably not the only cause. At that point, look harder at driver behavior, power-state handling, or router compatibility.
- If the same pattern survives all of the above, suspect platform compatibility.
When a clean profile, a known-good driver, and a compatible router configuration still leave you with repeated reconnect failures after reboot, the issue starts to point beyond normal settings. That can mean BIOS or motherboard firmware, slot or platform compatibility, or a BE200 and system combination that simply doesn’t behave well on that machine.
Verify the fix
After each change, do one cold reboot and one shutdown-and-power-on cycle. The fix is holding if Windows reconnects without asking for the password, the saved SSID stays in place, and the network comes back the same way after both restart paths.
If the prompt returns only after sleep or hibernate, that narrows the problem to power-state handling. If it returns only after a cold boot, the router security mode, BIOS-level behavior, or adapter power management is more likely than the password itself.
If the profile disappears again after you’ve already rebuilt it and the driver is current for your system, stop treating it as a normal Windows setting problem and move to BIOS, motherboard firmware, or hardware compatibility checks.
Frequently Asked Questions
Should I delete the Wi‑Fi network and add it again right away?
Not right away. First confirm that Windows still has the saved profile, test a normal reboot versus a full shutdown, and check the BE200 driver, power settings, and router security mode. Delete and rebuild the profile only when the old one looks corrupted or out of sync.
Can Fast Startup really make this look like a password problem?
Yes. Fast Startup can change how Windows restores the wireless stack, so shutdown, restart, sleep, and hibernate can behave differently. If the BE200 reconnects one way but not another, test Fast Startup before assuming the saved password is gone.