If your MediaTek Wi‑Fi adapter stopped working right after a driver update, start with the driver package, not the laptop. The fastest safe fix is to roll back to the previous driver if Windows offers it, because that restores the last known-good version without a full reinstall. If rollback isn’t available or it doesn’t help, remove the bad package and install the laptop maker’s driver first. Then stop Windows from putting the broken one back.
What to try first when Wi‑Fi dies right after the update
A failure that starts right after a driver update usually points to one of three causes: the update package is bad, Windows changed a network setting, or the adapter is not loading correctly. If Wi‑Fi worked before the update and failed after the reboot, treat it as a driver problem first.
Use this quick decision table before you change settings:
| What you see | What it usually means | First move |
|---|---|---|
| The MediaTek adapter is still listed in Device Manager, but Wi‑Fi is gone | Bad driver or Windows setting conflict | Roll back the driver |
| Roll Back Driver isn’t available, or rollback doesn’t help | The bad package is stuck | Uninstall, then reinstall the OEM driver |
| The adapter is missing from Device Manager | Driver, BIOS, or hardware problem | Check BIOS/firmware and hardware path next |
| Wi‑Fi works on one network but not another | Router or band/settings issue may be involved | Test another known-good network or hotspot |
Open Device Manager and look under Network adapters. If you see the MediaTek adapter, Windows still sees the hardware. If you only see Network Controller, or the adapter has a warning icon, Windows may have failed to match the device cleanly. If the adapter vanished completely, that is a different problem, and a simple driver change may not bring it back.
A common report looks like this: the network panel shows no usable Wi‑Fi networks, but Ethernet still works, and Bluetooth may still be fine. That pattern usually points to driver or settings trouble first, not an immediate hardware failure.
Is this really a driver problem, a disabled adapter, or a settings clash?
Check the obvious things first, because a working adapter can look dead after a bad setting change. Confirm that the MediaTek adapter still appears in Device Manager, make sure Airplane mode is off, and test another network or a phone hotspot if you can.
- Confirm the MediaTek adapter is still listed in Device Manager.
- Check whether Wi‑Fi is missing from
Network & Internetor just won’t connect. - Make sure Airplane mode is off.
- Try a different network or a phone hotspot if you can.
- If Bluetooth still works but Wi‑Fi does not, that points more toward the Wi‑Fi side of the card than a total wireless failure.
Power settings can also make the adapter look broken. Windows may turn off the radio too aggressively to save power, and that can show up as dropped Wi‑Fi after a restart or wake. In the adapter’s properties, check the power management and advanced tabs for settings that can interfere with Wi‑Fi, such as band preference, roam behavior, or wireless mode.
If the adapter appears in Device Manager but Wi‑Fi networks do not show up, the card is not necessarily dead. It may just be blocked by a bad driver state, a power setting, or a Windows profile issue. If the adapter disappears from Device Manager entirely, stop treating it as a normal Wi‑Fi settings problem and move to the recovery steps below.
Rollback, uninstall, or reinstall: which fix to use
Start with rollback if Windows offers it. If that does not work, uninstall the bad device entry, then reinstall the correct OEM package. Use the missing-device checks only when the adapter is gone entirely.
- Start with rollback if Windows offers it.
Open Device Manager, right-click the MediaTek Wi‑Fi adapter, and open Properties. On the Driver tab, choose Roll Back Driver if that button is available, then restart the laptop. If Wi‑Fi comes back, the update package was likely the problem.
- If rollback is unavailable or doesn’t fix it, uninstall the bad device entry.
Right-click the adapter and choose Uninstall device. Use this step when the bad package is stuck or Windows will not revert cleanly. If Windows offers a checkbox to remove the driver software, only use it when you already have the replacement driver saved locally.
- Reinstall the driver from the laptop maker first, not a generic package.
Use the OEM driver for your exact laptop model when it is available. The laptop maker’s package is more likely to match the radio, firmware, and power behavior built into that chassis. Microsoft’s guidance also points out that Wi‑Fi on these systems is tied to the full platform, not just the chip itself. If the OEM page has no usable driver, use the official driver source that matches your exact adapter and Windows version. Verify that the package is for your exact model, not a similar MediaTek part number.
- If the adapter disappears from Device Manager, do not assume uninstall/reinstall will solve it.
When the device is missing entirely, the issue may be deeper than the driver package. Check whether the adapter is disabled in BIOS/UEFI, whether Windows still detects it after a restart, and whether the machine can see it after a clean boot. If it still does not appear, hardware or platform firmware is more likely than a simple bad driver.
The goal here is not to try every repair at once. Use the least risky reversible fix first, then move to a clean reinstall only if rollback is not available or doesn’t help.
How to stop Windows from putting the broken driver back
Keep the known-good driver in place once Wi‑Fi works again. Then block Windows from replacing it with the broken one on the next reboot or update cycle. If your version of Windows lets you hide a specific driver update, use that for the MediaTek package that caused the failure.
Also check whether Windows is set to fetch drivers automatically during updates. If it is, watch for optional driver updates for this adapter and avoid installing them until you confirm they improve stability.
If the broken package came back after a Feature Update or another refresh, the system may be reapplying it during updates. In that case, keep the working driver saved locally so you can reinstall it quickly if Windows swaps it out again.
If you removed the device and Windows did not reinstall it automatically, that can happen too. Use the saved OEM driver and install it manually rather than waiting for Windows Update to guess the right one.
How to confirm the repair and know when it isn’t the driver
Don’t call it fixed just because the Wi‑Fi icon reappeared. Confirm that the adapter stays present, joins a network, and still works after a restart or sleep cycle.
- Reboot the laptop.
- Open the network list and confirm Wi‑Fi networks appear.
- Connect to your normal network.
- Load a few normal web pages.
- Put the laptop to sleep and wake it once, then check Wi‑Fi again.
If the adapter stays connected through all of that, the repair probably held.
If it still drops out, think about the router if other devices also have trouble on the same network. Think about Windows if the adapter works after changing power settings or after a clean boot, then fails later. Think about hardware if the adapter disappears from Device Manager, shows repeated warnings, or fails even with the laptop maker’s driver.
The cases we have point to sudden failures where the network panel shows no usable connections while the adapter may still be partially present. That pattern usually means driver or settings trouble first, not an immediate hardware failure.
Conclusion
If rollback fixes it, leave the working driver alone. If rollback is unavailable or fails, use the OEM driver, block Windows from restoring the bad package, and recheck Device Manager after every restart.
Frequently Asked Questions
What if Roll Back Driver is greyed out?
Windows does not have a previous package stored for that adapter. In that case, uninstall the device, restart only if needed, and install the laptop maker’s driver from a local copy so you are not stuck offline during recovery. Use the saved replacement before you remove the current driver if this laptop has no other network path.
Should I use the MediaTek driver or my laptop maker’s driver?
Use the laptop maker’s driver first when the adapter belongs to a specific laptop model, because the OEM package is often tuned for that exact radio and firmware mix. Use a generic MediaTek package only if the OEM page has nothing usable, and verify that it matches your exact adapter and Windows version.
Sources
- Fix Missing Wi‑Fi After Windows 11 Install: MediaTek Driver Guide (windowsforum.com)
- Wifi stopped working overnight Mediatek MT7922 - Network - Manjaro Linux Forum (forum.manjaro.org)
- WIFI not working due to MediaTek Wi-Fi 6 MT7921 Wireless LAN Card (windowsphoneinfo.com)
- so, i am using the MediaTek Wi-Fi MT7921 wireless LAN card, and it keeps disconnecting and refusing to work. - Microsoft Q&A (learn.microsoft.com)