Two laptops can get different Wi‑Fi speeds on the same eero mesh. They may be using different bands, different eero nodes, or different wireless hardware. Start by comparing them in the same room, on the same test, and on the same band if you can. Then check whether the slowdown follows the laptop or the mesh path. If the slower result stays with one laptop after a fair test, fix the laptop first. If it stays with one spot or node, look at placement, roaming, or backhaul next.
Symptoms
One laptop often gets a much better speed test than the other, even though both show a strong signal and seem connected normally. The gap may show up in one room, on one eero node, or after a laptop roams from one node to another.
That can be misleading. A laptop with a healthy-looking signal can still be on a slower band, a different node, or a weaker adapter. The bars alone do not tell you whether the network is the problem.
Before you start
Use a fair comparison before you change anything.
- Put both laptops as close to the same spot as practical.
- Test them one at a time with the same speed test service and the same method.
- If possible, check that both are on the same band: 2.4 GHz, 5 GHz, or 6 GHz.
- Make sure neither laptop is downloading updates, syncing cloud storage, or running a big backup while you test.
- If you can, test at least two different servers and run 2–3 tests on each so you get a more reliable average.
If you’re comparing Wi‑Fi to Ethernet, don’t treat those as the same test. Ethernet bypasses the laptop’s wireless adapter and the mesh radio path, so it works as a baseline, not as a direct comparison to Wi‑Fi.
Why two laptops can get different speeds on the same eero network
Usually the difference comes from one of four places: the laptop, the band, the eero node, or the mesh path.
On the laptop side, one machine may have a newer Wi‑Fi adapter class, better antenna design, cleaner drivers, or less aggressive power saving than the other. Older devices or devices with older Wi‑Fi standards may simply not reach the same speeds as newer ones. A laptop that only supports 2.4 GHz will usually be slower than one that can use 5 GHz or 6 GHz, even when the signal looks strong.
On the mesh side, two laptops can still attach to different eero nodes. One node may have a more direct backhaul path, while another carries traffic through a less favorable mesh route. eero also notes that if a device keeps connecting to a farther eero, forgetting the network on that device and reconnecting can help it settle on a better node.
Band choice matters too. If one laptop lands on 2.4 GHz and the other lands on 5 GHz or 6 GHz, the speed gap can be real even before you blame the internet line. The eero app may make that harder to notice because the network name is often shared across bands, so the laptop can make the band choice without much obvious warning.
The mesh path can also change after roaming. A device can look connected but still be settling onto a new node, and a speed test taken during that transition can be noisy. If one laptop roams more often or more reluctantly than the other, you can end up comparing two different paths instead of two different devices.
How to compare both laptops fairly
Use a controlled side-by-side test so you can tell what changed.
- Put both laptops near the same eero node and turn off any obvious background activity that could eat bandwidth.
- Check each laptop’s connection details and confirm which band it is using, if the device shows that information.
- Run the same speed test on both laptops, one after the other, using the same server and the same test site.
- Repeat the test on a second server and average the result instead of trusting one run.
- If one laptop is still much slower, move the slower laptop to the exact spot where the faster one was tested and repeat the test.
If the slower result follows the laptop, you’re looking at a device-side issue. If it follows the spot or the node, the mesh path or placement is more likely.
Simple tests to isolate the cause
Start with the least disruptive check: swap the laptops, not the network.
- Test laptop A in the problem spot, then test laptop B there without moving the eero node.
- If laptop B is still faster, the issue is probably in laptop A.
- If both laptops are slow in that spot, move to a different room or a different eero node and test again.
- If the faster laptop slows down only when it lands on a different node, the node or backhaul path is part of the problem.
- If the slower laptop keeps connecting to a farther eero, forget the network on that laptop and reconnect it.
That pattern tells you what to fix next. A problem that follows the laptop points to the adapter, drivers, band support, or power settings. A problem that follows the node points to placement, roaming behavior, or the mesh path.
What is normal versus suspicious
Some speed difference is normal when the laptops are not equal. One may have newer wireless hardware, a better antenna layout, or support for a faster band. One may also be using a different eero node or a different backhaul path, which can change the result without any fault at all.
A difference becomes suspicious when the same laptop is consistently much slower in the same place, across more than one test, after reconnecting, and after you’ve ruled out background downloads or updates. A weak or poorly matched Wi‑Fi adapter often shows up as repeatable slowness or inconsistency rather than a total drop-out, so look for a pattern instead of one bad run.
If multiple devices and locations are slow, the issue may be network-wide rather than isolated to one laptop.
First fixes to try on Windows and macOS
Work on the laptop before you change the network.
On Windows, update the Wi‑Fi driver from the laptop maker or the adapter maker, not just through a generic updater. Then check the wireless adapter’s power settings and make sure it is not set to an aggressive power-saving mode that could reduce performance.
On macOS, install the latest system update available for that machine. Then disconnect and reconnect to the eero network so the Mac renegotiates its link.
After that, forget the eero network on the slow laptop and reconnect it. eero specifically suggests this if the device keeps connecting to a farther eero. Then repeat the same room, same test, same band comparison if the laptop lets you see or choose the band.
If the laptop still trails the other one by a wide margin, check whether it actually supports the band and speed you expect. A device with older Wi‑Fi standards may not match a newer laptop even on the same eero system.
When to suspect hardware, placement, or a faulty adapter
If the slower laptop is still slow after a driver update, a reconnect, and a fair test, start thinking about hardware.
A few common signs point that way. The laptop may be much slower than the other one on the same band. It may get worse near walls or cabinets. It may also change speed a lot even when nothing else in the room changes. Thick walls, cabinets, metal furniture, and bad placement can all hurt the result, so try the slower laptop near the main eero node in an open spot before you blame the adapter.
If the laptop still performs badly near the main node, the Wi‑Fi card or antenna design is the more likely cause. If it improves a lot there but not in the original room, the mesh placement or the node it was using is the better place to fix.
Conclusion
If the slower laptop keeps losing even after a fair test, update its driver or software, forget and rejoin the eero network, and then compare the band and node it lands on. If that doesn’t change the result, the laptop hardware or the mesh placement is the next thing to check.
Frequently Asked Questions
How do I tell if my slower laptop is on a different eero node?
Check the connection details on the laptop itself, then test both laptops in the same spot one at a time. If the slower laptop keeps landing on a farther node or drops to a different band, the problem is usually roaming or band selection rather than the internet line.
Should I test with Wi‑Fi or Ethernet first?
Use Wi‑Fi for the comparison if the problem is different speeds on two laptops over Wi‑Fi. Ethernet is useful only as a baseline, because it bypasses the laptop’s wireless adapter and the mesh radio path.